Euro Press Pack Manual and Foot Pumps

All Euro Press Pack pumps are manufactured to DNV and ISO standards, and are treated with the “Nitreg ONC” process in-house at the company’s production plant in Carasco, near Genoa in northern Italy.

This exclusive thermo-chemical treatment makes the steel exceptionally hard and resistant to corrosion, before the equipment is then further strengthened with the application of a special oil that coats the treated surfaces and makes them immune to corrosion. Euro Press Pack pumps and hydraulics are therefore especially suitable for use in applications where there is a high risk of corrosion and mechanical wear. And the range of Euro Press Pack manual and foot pumps are no exception…

PF series lightweight alloy foot pumps, 700 bar:

This aluminium pump is lightweight simple to use, strong and easy to maintain. Available in single-stage and double-stage versions to reduce approaching times. It is equipped with:

  • Externally adjustable relief valve;
  • Steel base plate with antislip pads which may be removed, if the pump is mounted onto to a flat surface;
  • 1/4” NPT gauge port for direct installation of a pressure gauge on the pump head.

PL series lightweight hand pumps, 700, 1000, 1600, 2800 bar:

The weight and strength characteristics of the PL range have been retained in the new PN range. Some of the newer Euro Press Pack pumps models have been added with the introduction of our new PNP series designed with a plastic reservoir for pump primarily used in fixed operations. The traditional reliability of the PL pumps has been further enhanced by a new design of the piston and pump body. This reduces the ingress of dirt particles into the pump. Pumps with a 1 and 2 litre reservoir capacity have been completely re-designed and are characterised by a higher usable volume which enables the operator to use the total capacity without venting or alternatively, to fill the reservoir and use a higher capacity after having vented. In these pumps the venting plug is on the rear part of the reservoir so that, without any further modification, the pumps can be used vertically with the pump body facing down. The handy lever lock enables the pump lever to be used as a handle whilst carrying the pump, even with accessories assembled to the pump. All pumps have an externally adjustable relief valve and most of them have a side or front port for a direct connection of a gauge.

PP series hand pumps for diversified applications, 700 – 1400 bar:

Single-stage, tankless hand pumps, are lightweight and easy to handle (their weight is less than 5kg for the standard version and 6kg for the INOX version). All models are equipped with: 490 mm removable activation handle, used to turn the bypass valve on through the front connection, fixing holes on the base, 3/8”-18 NPT side ports for oil inlet and outlet. All standard pump components, either internal or external, undergo the EUROPRESS exclusive thermo-chemical treatment, named Nitreg-ONC®, which makes steel exceptionally hard, resistant to corrosion and mechanical wear. The PP113 Pump is also available in stainless steel for use with water, and with different pump heads to be used at pressures lower than 700 bar (on demand).

PS series steel hand pumps 400, 700, 100 bar:

These Euro Press Pack pumps are easy to use robust hand pumps in steel requiring moderate handle effort. They are available in four models, with three pressure ratings, 400 – 700 – 1000 bar. These pumps can also operate in vertical position with head downwards. All models are equipped with:

  • External adjustable safety valve;
  • Wide feet for ease of mounting;
  • Handle locking mechanism for ease of carrying Available with 0,42 – 0,8 lt. reservoirs depending on the model.

PV series steel hand pumps with large oil delivery 700 bar:

Two-stage hand pumps with automatic change-over from the 1st to the 2nd stage that require a moderate effort on the handle to reach maximum working pressure. All models are equipped with:

  • Relief valve
  • Carry handle
  • 1/2” BSP connection for pressure gauge

These Euro Press Pack pumps are also available with 10 or 20 litre reservoirs and 3-way, 4-way and 4-way with controlled check valves.

PVL series steel hand pumps with large oil delivery and lightweight alloy reservoir 700 bar:

Two-stage hand pumps with a valve that allows automatic change from 1st to 2nd stage. It requires only a moderate effort on the handle to reach the maximum working pressure. All models are equipped with:

  • Relief valve;
  • Carrying handle;
  • Light alloy reservoir (it helps reduce considerably pump weight);
  • ½” BSP connection for pressure gauge Available with 3-way, 4-way, and 4-way with controlled check valves.

Euro Press Pack Manual and Foot Pumps - PF, PP, PV, PL, PS and PVL Series

Call us now on: +44 (0)845 644 3640 or enquire online and "let us take the pressure!"

Blog & Case Studies

Hydraulics Online, Elon Musk and SpaceX Hyperloop

HypED is a University of Edinburgh student

August 24, 2017 read more

Innovative Custom Hydraulics and Systems Design

We invest time and energy to build great relations

July 18, 2017 read more

News Archive

Contact Us

Phone:+44 (0)845 644 3640

Address:
Units 2+3 Townend Farm
Audley Road
Alsager
Cheshire
ST7 2QR
United Kingdom..

Connect with us!

Facebook Twitter Linked In Pinterest Tumblr whats app RSS

Testimonials

Hydraulics Online, Elon Musk and SpaceX Hyperloop

HypED is a University of Edinburgh student-led project that is blazing a successful path for British engineers in Elon Musk’s SpaceX Hyperloop project – and […]

Innovative Custom Hydraulics and Systems Design

We invest time and energy to build great relationships with our suppliers as well as our customers. Fluidlink Hydraulics is a British manufacturer of mobile hydraulic […]