Salami Hydraulics

Salami Hydraulics

Hydraulics Online – Supplying you with Salami hydraulics and Salami hydraulic gear pumps, hydraulic motors, flow dividers, stackable / monoblock / pressure compensated hydraulic directional control valves and other Salami hydraulics equipment and components…

Salami Hydraulics is a family-owned Italian company that has been producing directional control valves, hydraulic gear pumps and hydraulic motors and components for remote controls (joysticks and cable controls) since it was founded in 1956.

Salami Group 1 E Series, Group 1.6 E series gear pumps and motors made with alluminium alloy body, flanges and rear covers:

Salami Group 1 E Series, Group 1.6 E SeriesDisplacements from 0,9 cm3/giro (0,05 cu.in./rev.) to 6,5 cm3/giro (0,39 cu.in./rev.)

 

 

 

Salami Group 2 E Series gear pumps made with alluminium alloy body and cast iron flanges and rear covers:

Salami Group 2 E

  • Displacements from 3,2 cm3/rev (0,19 cu.in./rev.) to 26 cm3/rev (1,58 cu.in./rev.)
  • Extremely compact design on the multiple assembling pump for the 2PE type.

 

 

Salami Group 2.5 B Series gear pumps made with alluminium alloy body and cast iron flanges and rear covers:

  • Salami 25 B SeriesDisplacements from 3,2 cm3/rev (0,19 cu.in./rev.) to 26 cm3/rev (1,58 cu.in./rev.)
  • Extremely compact design on the multiple assembling pump for the 2PE type.
  • Assembling on multiple stage pump also available in combination with 2PE or 1.5PB types.

 

Salami Group 3 B series gear pumps and motors made with alluminium alloy body, flanges and rear covers:

  • Salami Group 3 B SeriesDisplacements from 21 cm3/rev (1.26 cu.in./rev.) to 75 cm3/rev (4.48 cu.in./rev.)
  • Assembling on multiple stage pump 3PB/3PB available.
  • Assembling on multiple stage pump also available in combination with 2PE type.

 

 

Salami Group 3.5 B Series gear pumps and motors made with alluminium alloy body, flanges and rear covers:

  • Salami Group 35 BDisplacements from 55 cm3/giro (3,34 cu.in./rev.) to 98 cm3/giro (6,03 cu.in./rev.)
  • Assembling on multiple stage pump 3,5PB/3,5PB available.
  • Assembling on multiple stage pump also available in combination with 2PE, 2PB or 3PB types.

 

Salami Group 2 – E Series gear motors made with alluminium alloy body and cast iron flanges and rear covers:

  • Salami Group 2 E SeriesDisplacements from 4.5 cm3/rev (0,27 cu.in./rev.) to 26 cm3/rev (1,58 cu.in./rev.).
  • Rated pressure up to 250 bar (3630 psi) –
  • Back pressure capability up to 120 bar (1740 psi) only in by-directional release.

 

 

Salami Group 2 E series Gear flow dividers made with alluminium alloy body and cast iron end covers:

  • Group 2 E Flow DividerDisplacements from 3,2 cm3/rev (0,19 cu.in./rev.) to 30 cm3/rev (1,83 cu.in./rev.)
  • Extremely compact design.
  • Available also with main relief valves to realign the cylinders at the end of stroke.

 

 

Salami Group 3 H Series gear pumps and motors made in spheroidal cast iron:

  • Salami Group 3 HDisplacements from 21 cm3/rev (1.3 cu.in./rev) to 90 cm3 /rev (5.4 cu.in./rev).
  • Assembling on double stage pump 3HP/3HP available.
  • Assembling on multiple stage pump also available in combination with 2PB or 2.5PB types.

 

Salami PG301 gear pumps made in spheroidal cast iron:

  • Salami PG301 Gear PumpsDisplacements from 23 cm3/rev (1.43 cu.in./rev) to 40 cm3 /rev (2.46 cu.in./rev).
  • Very compact design, flange, central body, rear cover
  • Available as single or double stage pump.

 

Salami PG330 gear pumps made in spheroidal cast iron:

  • Salami PG330 Gear PumpsDisplacements from 23 cm3/rev (1.43 cu.in./rev) to 40 cm3 /rev (2.46 cu.in./rev).
  • Very compact design, flange, central body, rear cover
  • Available as single or double stage pump.

 

Salami VDM6 Directional Control Valve:

  • Salami VDM6 Directional Control ValveCast-iron monoblock construction from 1 to 7 working sections.
  • Parallel circuit, load check valve protection on down-stream of the pressure “P” line.
  • Tandem circuit, only the first working section, l.c.v. protection + l.c.v. protection on down-stream of the “P” line.
  • Possibility of power beyond.
  • Peveral types of spool: double, single acting, spool motor, float position, regenerative position etc.
  • Several spool control devices and spool positioning devices.

Salami VDM6A Directional Control Valve:

  • Salami VDM6A Directional Control ValveCast-iron monoblock construction from 1 to 7 working sections.
  • Parallel circuit, load check valve protection on each section.
  • Possibility of power beyond configuration.
  • Several types of spool: double, single acting, spool motor, float position, regenerative position etc.
  • Possibility of auxiliary valve either on port A or B or on both.
  • Several spool control devices and spool positioning devices.

Salami Hydraulics VDM09 Directional Control Valve:

  • Salami VDM09 Directional Control ValveCast-iron monoblock construction from 1 to 6 working sections.
  • Parallel circuit, load check valve protection on down-stream of the pressure “P” line.
  • Possibility of power beyond.
  • Several types of spool: double, single acting, spool motor, float position, regenerative position etc.
  • Several spool control devices and spool positioning devices.

Salami Hydraulics VDM8 Directional Control Valve:

  • Salami VDM8 Directional Control ValveCast-iron monoblock construction from 1 to 5 working sections.
  • Parallel circuit, load check valve protection on each section.
  • Possibility of power beyond configuration.
  • Several types of spool: double, single acting, spool motor, float position, regenerative position etc.
  • Possibility of auxiliary valve either on port A or B or on both.
  • Several spool control devices and spool positioning devices.

Salami Hydraulics VD6A Directional Control Valve:

  • Salami VD6A Directional Control ValveCast-iron made (inlet section, working section, outlet section) up to 8 working sections.
  • Parallel circuit, load check valve protection on each section.
  • Series circuit, load check valve protection on each section (possibility of 2nd load check valve on series line)
  • Tandem circuit, load check valve protection on each section.
  • Possibility of power beyond configuration and possibility of closed center.
  • Several types of spool: double, single acting, spool motor, float position, regenerative position etc.
  • Several spool control and spool positioning devices.

Salami Hydraulics VD8A Directional Control Valve:

  • Salami VD8A Directional Control ValvesCast-iron made (inlet section, working section, outlet section) up to 8 working sections.
  • Parallel circuit, load check valve protection on each section.
  • Series circuit, load check valve protection on each section (possibility of 2nd load check valve on series line)
  • Tandem circuit, load check valve protection on each section.
  • Possibility of power beyond configuration and possibility of closed centre.
  • Several types of spool: double, single acting, spool motor, float position, regenerative position etc.
  • Several spool control and spool positioning devices.

Salami Hydraulics VD10A and Salami VD12A Directional Control Valves:

  • Salami VD10A VD12ACast-iron made (input module, work module, the closure module ) up to 8 work sections .
  • Parallel circuit, each module is provided with valve unidirectional protection section of the same .
  • Circuit series, each module is provided with a unidirectional valve (possibility of a second one-way valve on the serial line) .
  • Independent circuit, each module is provided with a unidirectional valve to protect each section.
  • Shuttles available: Double and single acting, motor spool.
  • A wide range of spool control devices and positioning spools available.

Salami Hydraulics VDP08 Pressure Sensing Directional Control Valve:

  • Salami VDP08Load sensing directional control valve.
  • made on cast-iron(inlet section, working section, end section).
  • Available with inlet module for fixed or variable displacement pump.
  • inlet module with pressure compensator built-in, working modules with pressure compensator built-in..
  • Several types of spool: double, single acting, spool motor, float position etc.
  • Possibility of auxiliary valve either on port A or B or on both.
  • Possibility of pressure relief valve on the LS line coming from the ports.

Hydraulics CatalogueVisit our catalogue to see some of the hydraulic components we have within our range. It is only a small selection of what we do, however. So don’t worry if you can’t find what you’re looking for – simply call us or complete our Stock Enquiry Form.

Call us now on: +44 (0)845 644 3640 or enquire online and "let us take the pressure!"

Blog & Case Studies

International Hydraulics – Ain’t no Mountain High Enough!

Here at Hydraulics Online we always like to go the

June 13, 2017 read more

News Archive

Contact Us

Phone:+44 (0)845 644 3640

Address:
Units 2+3 Townend Farm
Audley Road
Alsager
Cheshire
ST7 2QR
United Kingdom

Connect with us!

Facebook Twitter Linked In Pinterest Tumblr whats app RSS

Testimonials

Testimonial: Procurement Management

Praise from a customer in West Africa, who offers services and general procurement management for companies in the mining, engineering and construction equipment and parts industry: […]

Testimonial: Tree Surgery and Forestry Contractors

It’s all in a day’s work for the technical team, with praise from a company who carries out all aspects of tree work and hedge […]